欢迎光临乐清市美格尔电子电器有限公司官方网站!

>美格尔

联系我们

  • 联系电话:

    0577-62875133

  • 传真:

    0577-62987133

  • E-mail:

    mgr@mgr.top

电力调整器

当前位置:首页 > 产品总汇 > 产品中心 > 电力调整器

MGR-DTY-F-22- □ -EG 单相移相调压稳压型模块

所属:电力调整器

产品介绍

◎ 型号含义 Type meaning

`image.png`/

① 可控硅调压 SCR voltage regulator

② 闭环稳压 Closed-loop stabilizer

③ 负载电压 220V 或 380VAC  Load voltage 220V or 380VAC

④ 15A,25A,40A,50A,70A,90A,120A,150A,200A

⑤ 控制电压 0-5VDC Control voltage 0-5VDC

⑥ 控制电流 4-20mA Control current 4-20mA


◎ 产品概述 Product overview

◆ 额定电流:15A-200Amps

◆ 额定电压:220V/380VAC(可选)

◆  无需外接 +12V 直流电源

◆ 增设闭环(负反馈)稳压系统,能有效稳定电压波动

◆ 绝缘介质电压大于 2000VAC

◆ 支持 4-20mA, 0-5V 自动控制模式,也可手动控制,调节平滑

◆ 内置屏蔽电路,抗干扰能力强

◆  采用大功率晶闸管芯片和 DCB 陶瓷釉锌绝缘底板材料

◆ 性能稳定,可靠性高


◆ Rated current: 15A-200Amps

◆ Rated voltage: 220V/380VAC (optional)

◆  No external +12V DC power supply required

◆ Effectively stabilize voltage fluctuations with closed-loop (negative feedback) voltage regulator system

◆  Insulation voltage greater than 2000VAC

◆ Support automatic control mode (control signal 4-20mA, 0-5V) and manual control mode, and both modes are smooth to adjust

◆ Built-in shielding circuit with strong anti- interference ability

◆ THigh-power thyristor chip, and insulating base plate with DCB ceramic glaze material

◆Stable performance and high reliability


注意 :

1. 当负载电流为 10A 时 , 必须加装散热器 ; 为 40A 及以上时 , 必须加风扇强冷或水冷 .

2. 使用感性负载时 , 务必在输出端并接一个压敏电阻 , 取值为负载电压的 1.6-1.9 倍 .

Notice:

1. If the load current is 10A, a heat sink must be equipped; if the load current is 40A or more, an air-cooled radiator or a water-cooled radiator must be installed.

2. When the load is an inductive load, be sure to connect a varistor in parallel with the output terminal, whose voltage value is 1.6-1.9 times the load voltage.


◎ 安装尺寸及接线图 Installation dimensions and wiring diagram

`image.png`/

关注微型平台

Copyright © 2020 乐清市美格尔电子电器有限公司 All Rights Reserved 版权. 浙ICP备0522718号